Dishwasher Repair
Viking Dishwasher Leaves Dishes Dirty: How the Wash Loop Works
Dishes come out dirtier when the dishwasher keeps spraying them with its own grimy water, because the filter is clogged, a spray arm is blocked or the water never got hot. Here is how a Viking wash cycle works and what to check first.
- Published
- Read time
- 5 min
- Appliance
- Dishwasher Repair
- Checked by
- Hollis Yamada
- Bench role
- Service technician — refrigeration and cooking
- At the bench
- 21 years in the trade
Dishes come out dirtier than they went in when the machine keeps throwing its own dirty water back at them. A dishwasher does not spray fresh water for every blast. It fills a small pool in the bottom of the tub, pumps that same pool through the spray arms over and over, and counts on its filters to strip out whatever washes off. When the filter is packed, a spray arm is jammed or the water never gets hot enough to break down grease, the pump just spreads the grit around, and you open the door to a sandy film on the top rack. In most Redmond kitchens the cure is ten minutes of cleaning rather than a new appliance, and the checks below run from the easiest to the least likely.
What happens inside one wash cycle
Every program repeats the same loop. The inlet valve lets in a measured fill, far less than a sink would hold. A heater, helped by the hot water arriving from your house, brings it up to temperature. The circulation pump drives that water up into the lower and upper spray arms, and the force of the jets is what makes the arms turn. Water rains back down into the sump, passes through the filters and goes around again. At the end of each phase the drain pump empties the tub, and a clean fill starts the rinse.
That recirculating design is why a modern machine can clean with so little water, and it is also why one weak link spoils the whole load. Food the filter fails to hold does not leave the dishwasher. It rides the next jet straight back onto a glass.
Start with the filters
For its VDWU and FDWU models, Viking’s own manual sets a weekly filter rinse as the minimum, yet plenty of households go months without touching them. The assembly sits in the floor of the tub beneath the lower spray arm. Turn the round micro and coarse filter counterclockwise and lift it free, then slide out the flat filter that sits under it. Work each of the three parts clean under the faucet using a soft-bristled brush, gentle enough for the fine mesh, then seat them again until they click. A filter that is not locked down lets debris slip past it, and that is worse than a dirty one.
While the filters are out, shine a light into the sump. Broken glass, produce stickers, olive pits and small bones gather there and can knock against the pump. If you hear grinding, or a whir with no splashing behind it, stop and look before you run another load.
Spray arms and how the racks are loaded
Each arm carries a row of small nozzles, and a single seed or a curl of plastic lodged in one is enough to leave a dry stripe across a rack. Pull the arms off, hold them up to a window and push out anything stuck in the holes with a toothpick. Once they are back on, spin each one by hand. It should turn freely and never catch on a pan handle or a spatula poking down through the basket.
Loading matters more than most people expect. Bowls stacked inside one another, a tall cutting board standing in front of the detergent cup, or a sheet pan lying flat across the bottom rack will shade everything behind it. Turn the soiled faces of plates toward the middle, where the spray is strongest, and leave the detergent lid room to swing open.
Detergent, rinse aid and Redmond water
Detergent cleans with chemistry and heat as much as with force. Use too little and grease stays put. Use too much, particularly in soft water, and a cloudy coating builds up on glassware and can etch it over time. Redmond’s supply is a mix drawn from the city’s own wells and from a regional water source, so hardness is not the same in every part of town. The city publishes a yearly water quality report with the figure, and dosing to that number beats filling the cup to the brim out of habit.
Rinse aid does the other half of the job. On Viking VDWU and FDWU dishwashers it adjusts from P:0 to P:4 and comes preset at 3. If spots and streaks remain after drying, move it up one level. If a faint bluish smear comes off a glass when you rub it with a finger, the dose is too heavy and should come down.
Hot water and the first fill
Grease that never melts gets smeared instead of washed away. Before you press start, run the kitchen tap until it turns hot, so the first fill is not the cold water that has been resting in the line under the sink. In a house where the water heater sits at the far end from the kitchen, that first fill can show up barely warm, and the cycle may never fully catch up.
If plates still feel greasy after a normal program with a hot start, the dishwasher’s own heater or its temperature sensor may not be working. That is a failed part rather than a habit, and no amount of extra detergent will cover for it.
What the lights and codes are telling you
Viking VDWU and FDWU machines with a display, including the VDWU724 and FDWU724, print codes. E:02 means water has stopped arriving; the program pauses and picks up again when the supply returns, so make sure the valve under the sink is open before anything else. E:01 points to an overfill or a leak, and the dishwasher will try to pump itself out. If E:01 keeps returning after a restart, it is a fault for a technician rather than something to clear and ignore.
Older built-in Viking dishwashers flash the cycle buttons instead of showing text. On those, a Drain Timeout says water is not leaving the tub. Check the sink drain, the knockout plug inside a newly fitted disposal, the drain hose for kinks or clogs, the high loop under the counter, whether the unit sits level, and the filters once more. Water that will not drain stays in the sump and gets pumped back over the dishes, which is one of the quieter causes of gritty results.
When cleaning does not fix it
If the filters are clean, the arms spin, the water arrives hot and the dishes are still dirty, the cause is usually mechanical: a circulation pump that has lost pressure, a drain pump leaving water behind, or a control cutting phases short. A pump or control repair on these machines typically falls in the $200–$390 range, with the firm price given once the dishwasher has been diagnosed. The $89 visit pays for the trip and a full diagnosis, and when you approve the repair that same $89 is deducted from it; the details are in what the $89 service call covers.
Viking Repair Redmond works on dishwashers across Downtown Redmond, Education Hill, Overlake and Redmond Ridge. Read more on Viking dishwasher repair in Redmond, or call (425) 585-2373 to book a visit.
Common follow-ups
What makes a dishwasher leave food and grit on clean-looking plates?
Most of the time the machine is reusing water it could not clean. A packed filter, nozzles plugged on a spray arm, a lukewarm first fill or water left sitting in the sump all send loosened food back onto the load. Clean the filters and arms first, then look at water temperature and how much detergent goes in.
How often should I clean a Viking dishwasher filter?
Once a week at minimum, according to the Viking manual for its VDWU and FDWU dishwashers. Turn the round filter counterclockwise, lift it out along with the flat screen under it, scrub all three parts under the tap and press them back until you hear the click.
What does it mean if the dishwasher whirs but the dishes stay dirty?
A steady whir with no splashing usually means the pump is turning with little or no water in the tub. Make sure the shutoff valve under the sink is fully open; on Viking models with a display, E:02 confirms the supply has been cut. If water is reaching the machine and it still runs dry, the pump or inlet needs a look.
Why is there a white film on my glasses after a cycle?
A chalky or cloudy coating is normally minerals or leftover detergent rather than food. Cut the detergent back if your water is on the soft side, and tune the rinse aid: on Viking VDWU and FDWU models move it up one step from the preset 3 for spotting, or down a step if a bluish smear wipes off.
Is a dishwasher that leaves food on dishes worth repairing?
Usually it is, since most causes are a cleaning job or one worn part. When a Viking dishwasher needs a pump or control, the typical range is $200–$390 and is firmed up after diagnosis on the $89 service call; that $89 is taken off the repair price if you approve the work.